RB Scott: Equipment, Wear Parts, Service

Connect With Us Facebook

Your process equipment and wear parts specialists

Used Metso/Nordberg LT1213S Track Mounted Crusher, Unit #760


Feeding Unit Feeding Unit – Pan Feeder and scalper The scalper is equipped with 2 grizzly sections Horizontal feeder maximizes the overall production through the efficient removal of fines from the feed material 1st Grizzly – ZigZag 38mm (2”) Upper grizzly 2nd Grizzly – ZigZag 38mm (1 ½”) Lower grizzly Screen Deck Media – Steel cloth 35mm (1 3/8”) Screen media to separate fines from feed and guide them to side conveyor. Screen mesh is mounted under the grizzlies Feed Hopper – Extended 9 m³ (12yrd³) Increases the volume of the standard feed hopper. Enables the loading either with an excavator or wheel loader and is made of wear resistant steel Side walls are folded down for the transport Feed hopper side walls are hydraulic operated and locked No tools required for set up Side Conveyor – Included (H5-4) Belt conveyor for transporting the fine material to the left or right hand side of the Lokotrack The side conveyor is equipped with hydraulic drive and safety trip wires on both sides of the conveyor Belt conveyor for transporting the fine material to the side of the Lokotrack The side conveyor is equipped with hydraulic drive and stop buttons both sides of the conveyor The folding and lengthening of side conveyor is hydraulic   Crusher Crusher – Impact crusher NP1213M NP1213M impact crusher is part of the NP series horizontal shaft impact crusher range This range features a unique combination of heavy rotor design, wear material and crushing chamber design The design minimizes maintenance time and improves all adjustment operations NP series impact crushers deliver unbeatable performance in primary, and recycling applications Hammers – Martensitic Xwin Metal Matric Composite (MMC) blow bars with ceramic particles on wear surface and martensitic steel insert Suitable for general quarry and recycling applications Belt Protection Plate – Included On the fixed jaw side a plate is mounted to guide the crushed recycling material together with steel parts onto the main conveyor and to protect the belt conveyor Hydraulic Assistance Crusher setting adjusted and setting shown on IC display Hydraulic assistance for setting adjustment Service Hoist – Included Lifting device for changing the crusher wear parts Transported separately in one piece   Power Unit Diesel Engine – CAT C13 Highly powerful and fuel efficient diesel engine Emission Class – Tier 4F Tier 4 Final (stage IV) emission regulated engine Climate Kit – Standard (-20C/-4F...35C/95F)   Main Conveyor Main Conveyor – Standard Discharge Height: 2800 mm (9 ft 2 in) Length: 11 m (36 ft 4 in) Belt Width: 1200 mm (47 in) Belt Speed: 2 m/s (6,6 ft/s) Hydraulic Motor Drive Belt conveyor for transporting the crushed material from the crusher to the discharge point The conveyor is equipped with discharge hood, hydraulic drive and emergency stop wires on both sides of the conveyor Magnetic Separator – Master Magnet Permanent self-cleaning magnet to remove the iron waste from the crushed material   Screening Unit Screening Unit – 5’x12’ Screen module TK13-30S with H5-10 return conveyor Horizontal single deck, single shaft screen Steel wire and rubber screen clothes available Screen Media - Steel cloth 40 mm (1 37/64")   Optional Equipment Interlocking – Included Secondary unit material level will control the feeding of primary unit Hydraulic Power Take Off – Included For connecting the auxiliary hydraulic equipment to the hydraulic system of the Lokotrack Water Spraying System – Included For binding dust particles at the crusher cavity, under the crusher and at the discharge end of main conveyor Remote Radio Control – Included (US / 458Mhz) Remote radio controller for the main functions Enables the remote control of following functions: start/stop of feeder unit, rpm adjustment of diesel engine, moving forward/reverse (tracks) Cable controller is always supplied with Lokotrack Halogen Lights   Finishing Color – Metso Beige Safety Labels – ANSI   Documentation Quantity of Printed Manuals – 1