RB Scott: Equipment, Wear Parts, Service

Connect With Us Facebook

Your process equipment and wear parts specialists

Superior Guardian 7x20 3-Deck Horizontal Screen Plant, Unit #777

#925847

Carrier chassis Main frame constructed of wide flange structural steel beams Tandem axle with (8) 11x22.5 radial tires complete air brake system mudflaps on rear axle Travel lights with brake and directional signals Fifth wheel hitch (4) fixed, structural steel cribbing legs Common Grease points - 1-2 locations to grease entire plant   Superior Guardian 7203 Horizontal Vibrating Screen Supply and Installation for a 7x20 3 deck, all pertinent items and components including: adjustable motor base, motor sheave, screen sheave, v-belts, drive guard Screen and all pertinent items and components are supplied by Superior Price includes the following items: 50 HP TEFC, 1800 RPM, 460 volt, 3 phase, 60 hz, screen drive motor screen subframe Screen is installed to operate in the horizontal position Right hand drive Screen discharge chutes Roll away chute Constructed of 1/4" Mild Steel with 1/4" AR liners Top deck chute discharges over the kingpin end of the chassis or onto middle deck cross conveyor, 25% Blending gates Middle deck chute discharges onto middle or bottom deck cross conveyor, 25% Blending gates Bottom deck chutes discharges onto bottom or "blends up" to middle deck cross conveyor, 25% blending gates AR liners on both sides of blending gates Fines hopper 3/8" AR Construction with conveyor belt lining adjustable rubber flashing full length (2) 30" wide x 11' long reversing cross conveyors Structural steel channel main frame Mounted on rollers to manually move to discharge from either side of chassis Receive oversize material from respective middle and bottom decks Class II head end drive 7.5 HP motor, v-belt drive with drive guard Dodge shaft mount reducer Head pulley - 10" diameter drum, crown face, 3/8" diamond lagging Tail pulley - 10" diameter wing pulley Shafts - turned and polished Dodgebearings Manual screw take-ups Carry idlers - C5, 20 degrees trough, channel mount, spaced 26" OC Belting - 2 ply, 3/16" x 1/16" 220 PIW Belt splice - steel mechanical fasteners Primary belt scraper - Exterra® Belt Cleaner 60" x 29' fines conveyor (Horizontal) Structural steel channel main frame Capable of accepting a reject conveyor Class II head end drive 15 HP motor, v-belt drive Dodge shaft mount reducer Head pulley - 12" diameter drum, crown face, 3/8" herringbone lagging Tail pulley - 12" diameter Chevron® wing pulley Shafts - turned and polished Dodgebearings Manual screw take-ups Carry idlers - C5, 20 degrees picking, channel mount, spaced approximately 27" OC Return idlers - C5, flat rolls, spaced 10' OC Belting - 3 ply, 3/16" x 1/16" 220 PIW Belt splice - steel mechanical fasteners Primary belt scraper - Exterra® Belt Cleaner Walkway 3/16" diamond tread plate along both sides and feed end of screen Hydraulic folding walkway on non-drive side Includes toe board, and two-rail handrail, bolt on Walkway access on both sides of the chassis with steep angle stair access Drain holes Hydraulic "lift-only" leveling jacks (4) 5" x 18" hydraulic cylinders (4) manual lever valves; (1) for each cylinder 13HP Honda Motor gasoline over hydraulic, enclosed cabinet Overhead Safety tie off Safety tie off over plant for workers to tie off when working on screen Folds down for transport Cribbing Storage Hinged storage compartment Holds drive guard, screen cloth, cribbing materials, etc… Electrical control panel NEMA 4 enclosure and NEMA SQUARE D electrical components Wired to on-plant motors (1) 50 HP screen drive motor (1) 10 HP fines conveyor drive motor (2) 7.5 HP reversing cross conveyors Amp guage on outside of panel Hour meter inside panel Warning horn and light Labelled start/stop pushbuttons and E-stop pushbutton mounted on door of electrical panel Mounted on skid frame with lifting eyes (mounted on ditch side of plant) Power cables from motors to place panel 30' from plant, cable storage tray inside frame above axles Includes 2 extra #2 starters Painted to match plant Electrical Required power is 480 v/ 3 ph / 60 hz Control panel and wiring are not included Guarding Price includes standard guarding Customer is responsible to have guarding inspected Paint (1) coat primer; (1) finish coat enamel in Superior Beige Owner's manual copy included for operation and maintenance