RB Scott: Equipment, Wear Parts, Service

Connect With Us Facebook

Your process equipment and wear parts specialists

Superior Guardian 6x20 3-Deck Portable Screen Plant, Unit #819

#1042049

Carrier chassis

  • Main frame constructed of wide flange structural steel beams
  • Tandem axle with (8) 11x22.5 radial tires
  • complete air brake system
  • mudflaps on rear axle
  • Travel lights with brake and directional signals
  • Fifth wheel hitch
  • (4) fixed, structural steel cribbing legs
  • Common Grease points - 1-2 locations to grease entire plant

 

Superior Guardian 6203 Horizontal Vibrating Screen

Supply and Installation for a 6x20 3 deck, all pertinent items and components including:

  • adjustable motor base, motor sheave, screen sheave, v-belts, drive guard
  • Screen and all pertinent items and components are supplied by Superior

 

Price includes the following items:

  • 40 HP TEFC, 1200 RPM, 460 volt, 3 phase, 60 hz, screen drive motor
  • screen subframe
  • Screen is installed to operate in the horizontal position
  • Right hand drive

 

Screen discharge chutes

  • Roll away chute
  • Constructed of 1/4" Mild Steel with 1/4" AR liners
  • Top deck chute discharges over the kingpin end of the chassis or onto middle deck cross conveyor, 25% Blending gates
  • Middle deck chute discharges onto middle or bottom deck cross conveyor, 25% Blending gates
  • Bottom deck chutes discharges onto bottom or "blends up" to middle deck cross conveyor, 25% blending gates
  • AR liners on both sides of blending gates

 

Fines hopper

  • 3/8" AR Construction with conveyor belt lining
  • adjustable rubber flashing full length

 

(2) 30" wide x 11' long reversing cross conveyors

  • Structural steel channel main frame
  • Mounted on rollers to manually move to discharge from either side of chassis
  • Receive oversize material from respective middle and bottom decks
  • Class II head end drive
  • 7.5 HP motor, v-belt drive with drive guard
  • Dodge shaft mount reducer
  • Head pulley - 10" diameter drum, crown face, 3/8" diamond lagging
  • Tail pulley - 10" diameter wing pulley
  • Shafts - turned and polished
  • Dodgebearings
  • Manual screw take-ups
  • Carry idlers - C5, 20 degrees trough, channel mount, spaced 26" OC
  • Belting - 3 ply, 3/16" x 1/16" 220 PIW
  • Belt splice - steel mechanical fasteners
  • Primary belt scraper - Exterra® Belt Cleaner

 

60" x 29' fines conveyor  (Horizontal)

  • Structural steel channel main frame
  • Capable of accepting a reject conveyor      
  • Class II head end drive
  • 15 HP motor, v-belt drive
  • Dodge shaft mount reducer
  • Head pulley - 12" diameter drum, crown face, 3/8" herringbone lagging
  • Tail pulley - 12" diameter Chevron® wing pulley
  • Shafts - turned and polished
  • Dodgebearings
  • Manual screw take-ups
  • Carry idlers - C5, 20 degrees picking, channel mount, spaced approximately 27" OC
  • Return idlers - C5, flat rolls, spaced 10' OC
  • Belting - 3 ply, 3/16" x 1/16" 220 PIW
  • Belt splice - steel mechanical fasteners
  • Primary belt scraper - Exterra® Belt Cleaner

 

Walkway

  • 3/16" diamond tread plate along both sides and feed end of screen
  • Includes toe board, and two-rail handrail, bolt on
  • Walkway access on both sides of the chassis with steep angle stair access
  • Drain holes

 

Hydraulic "lift-only" leveling jacks

  • (4) 6" x 18" hydraulic cylinders
  • (4) manual lever valves; (1) for each cylinder         
  • 13HP Honda Motor gasoline over hydraulic, enclosed cabinet

 

Overhead Safety tie off

  • Safety tie off over plant for workers to tie off when working on screen
  • Folds down for transport

 

Cribbing Storage

  • Hinged storage compartment
  • Holds drive guard, screen cloth, cribbing materials, etc…

 

Electrical control panel

  • NEMA 4 enclosure and NEMA SQUARE D electrical components
  • Wired to on-plant motors
  • (1) 40 HP screen drive motor
  • (1) 15 HP fines conveyor drive motor
  • (2) 7.5 HP reversing cross conveyors
  • Amp guage on outside of panel
  • Hour meter inside panel
  • Warning horn and light
  • Labelled start/stop pushbuttons and E-stop pushbutton mounted on door of electrical panel
  • Mounted on skid frame with lifting eyes (mounted on ditch side of plant)
  • Power cables from motors to place panel 30' from plant, cable storage tray inside frame above axles
  • Includes 2 extra #2 starters
  • Painted to match plant

 

Electrical

  • Required power is 480 v/ 3 ph / 60 hz
  • Control panel and wiring are not included

 

Guarding

  • Price includes standard guarding
  • Customer is responsible to have guarding inspected

 

Paint

  • (1) coat primer; (1) finish coat enamel in Superior Beige

 

Owner's manual

  • (1) copy included for operation and maintenance