RB Scott: Equipment, Wear Parts, Service

Connect With Us Facebook

Your process equipment and wear parts specialists

GreyHawk/Metso/Superior HP300CC Portable Cone/Screen Plant, Unit #1029

#1235/SOR0216

Metso/Nordberg HP300 Cone Crusher
Equipped with manganese steel crushing members, hydraulic bowl clamping and adjustment, hydraulic clearing of crusher chamber, automatic tramp iron release, bronze bearings, package lubrication system (consisting of independent submersible pump, oil pressure switch, oil temperature switch, oil tank with strainer, oil level gauge and two thermometers, oil heater and oil filter), oil cooler (air–radiator type), tools, and WEG 300 HP, 1.15 service factor, 1800 RPM, 460 volt, 3–phase, 60 cycle, TEFC crusher drive motor.

Superior 6’x20’ Three Deck Triple Shaft Horizontal Screen
Unit Specifications 

  • Set at true horizontal [0 degrees]
  • High G-force screen with adjustable speed and stroke           
  • 160mm spherical roller bearings with 32 gears
  • Standard coil springs         
  • Rubber surge suppression for screen stability 
  • Right hand drive      
  • Slide adjustment motor base       
  • Huck bolted body    
  • Special length discharge lips        
  • 24" Feedbox with 1/4" AR liners   
  • Bolt-on inspection ports and spray hole knockouts     
  • Easy access guard for V-Belt drive with built in tensioner      
  • 5/16" sideplate construction with 1/4" reinforcing plates                  

                       

Additional Specifications              

  • 40 HP, 1200 RPM, TEFC     
  • 460V, 3 phase, 60 hz          
  • Standard mild steel protection clamped to shaft housing                  

                                   

Top Deck Specifications                

  • Heavy x-brace single crown deck to accommodate 4' single crown wire cloth media sections        
  • Media not included 
  • Standard take up rails        
  • Cross member protection not included  

                       

Middle Deck Specifications                      

  • Heavy x-brace single crown deck to accommodate 4' single crown wire cloth media sections        
  • Media not included 
  • Standard take up rails        
  • Cross member protection not included  

                       

Bottom Deck Specifications                     

  • Heavy x-brace single crown deck to accommodate 4' single crown wire cloth media sections        
  • Media not included 
  • Standard take up rails        
  • Cross member protection not included  

 

GreyHawk Heavy Duty Chassis

  • Main Chassis
  • 24” 84# mainbeam
  • Quad-axle Hutch spring ride suspension with three axles spaced at 49.5” and one axle spaced at 96”
  • Qty (16) 11R22.5 tires on Budd type wheels
  • Air controlled brakes on all four axles
  • LED side marker and tail lights
  • Horizontal screen support frame with diamond plate catwalks and handrails
  • Crusher motor support with hydraulic adjust for belt tensioning
  • Rock box feed hopper made from ¼” A36 steel plate and lined with plug welded ¼” AR400 liners

 

  • 42” Feed Conveyor
    • 10” channel frame
    • Superior 5” CEMA C channel mount idlers
    • Superior 5” CEMA C channel mount impact idlers in high impact areas
    • Superior 5” CEMA C rubber cushion return idlers
    • Five foot impact bed with Argonics impact bars
    • 12” wide slot take-ups
    • 3 ply, 3/16” top cover conveyor belting
    • Superior Powerfold allows easy access for crusher maintenance
    • Head Pulley
      • VanDer Graff motorized pulley
      • 16”-20HP
    • Tail Pulley
      • Superior 12”x44” chevron wing pulley
      • XT40 hubs
      • 2-15/16” dodge SCM bearings
    • 60” wide receiving hopper lined with bolted in 1” thick steel backed rubber
    • ½” skirtboard rubber where required
    • 44” Dings Self Cleaning Electro Magnet
    • Support structure for magnet
    • Lift points for removal of conveyor

 

  • 48” Overscreen Conveyor
    • 10” channel frame
    • Superior 5” CEMA C channel mount idlers
    • Superior 5” CEMA C channel mount impact idlers in high impact areas
    • Superior 5” CEMA C rubber cushion return idlers
    • 12” tube in tube take-ups
    • 3 ply, 3/16” top cover conveyor belting
    • Head Pulley
      • VanDer Graff motorized pulley
      • 12”-15HP
    • Tail Pulley
      • Superior 12”x44” chevron wing pulley
      • XT40 hubs
      • 2-15/16” dodge SCM bearings
    • Supported by four telescoping tubes with hydraulic cylinders to adjust between travel, operation and maintenance positions
    • ½” skirtboard rubber where required

 

  • 36” Undercrusher Conveyor
    • 8” channel frame
    • Superior 5” CEMA C channel mount idlers
    • Superior 5” CEMA C rubber cushion return idlers
    • Superior Exterra belt scraper
    • 12” wide slot take-ups
    • 3 ply, 3/16” top cover conveyor belting
    • Head Pulley
      • Superior 10”x38” vulcanized drum pulley
      • XT30 hubs
      • 2-15/16” dodge SCM pillow block bearings
      • Powertorque 315 shaft mount reducer
      • Weg 10HP motor
      • Sheaves & vbelts
    • Tail Pulley
      • Superior 10”x38” chevron wing pulley
      • XT30 hubs
      • 2-7/16” dodge SCM bearings
    • ½” skirtboard rubber where required

 

  • 36” Recirculation Conveyor
    • 8” channel frame
    • Superior 5” CEMA C channel mount idlers
    • Superior 5” CEMA C rubber cushion return idlers
    • 12” tube in tube take-ups
    • 2 ply, 3/16” top cover conveyor belting
    • Head Pulley
      • Van Der Graff motorized pulley
      • 8.5”-5.5HP
    • Tail Pulley
      • Superior 10”x38” chevron wing pulley
      • XT30 hubs
      • 2-7/16” dodge SCM bearings
    • ½” skirtboard rubber where required
    • Slide chute below the conveyor prevents material from building up on the axles

 

  • 60” Underscreen Product Conveyor
    • 8” channel frame
    • Superior 5” CEMA C channel mount picking idlers
    • Superior 5” CEMA C rubber cushion return idlers
    • Superior Exterra belt scraper
    • 12” wide slot take-ups
    • 3 ply, 3/16” top cover conveyor belting
    • Head Pulley
      • Superior 12”x63” vulcanized drum pulley
      • XT40 hubs
      • 2-1/16” dodge SCM pillow block bearings
      • Powertorque 415 shaft mount reducer
      • Weg 15HP motor
      • Sheaves and vbelts
    • Tail Pulley
      • Superior 12”x63” chevron wing pulley
      • XT40 hubs
      • 2-15/16” dodge SCM bearings
    • ½” skirtboard rubber where required

 

  • 18” Product Cross Conveyor
    • Channel frame
    • Superior 5” CEMA C channel mount idlers
    • Superior 5” CEMA C rubber cushion return idlers
    • 12” tube in tube take-ups
    • 2 ply, 3/16” top cover conveyor belting
    • Head Pulley
      • Van Der Graff motorized pulley
      • 8.5”-5.5HP
    • Tail Pulley
      • Superior 8”x20” chevron wing pulley
      • XT25 hubs
      • 1-15/16” dodge SCM bearings
    • ½” skirtboard rubber where required

 

  • 24” Product Cross Conveyor
    • Channel frame
    • Superior 5” CEMA C channel mount idlers
    • Superior 5” CEMA C rubber cushion return idlers
    • 12” tube in tube take-ups
    • 2 ply, 3/16” top cover conveyor belting
    • Head Pulley
      • Van Der Graff motorized pulley
      • 8.5”-5.5HP
    • Tail Pulley
      • Superior 8”x26” chevron wing pulley
      • XT25 hubs
      • 1-15/16” dodge SCM bearings
    • ½” skirtboard rubber where required

 

  • Adjustable king pin support
    • Adjustable tubular supports reduce the amount of blocking required in the kingpin area during plant operation, which simplifies set up and tear down.
    • The kingpin supports are lifted and pinned for towing to clear the semi-tractor.

 

Electrical:

  • NEMA electrical enclosure
  • Enclosure is bolted to a steel support frame for setting on grade during operation
  • Lifting eyes
  • Connected to plant with 15’ of cable to allow the customer to position the enclosure
  • Door interlocked disconnect linkage
  • Warning horn
  • Square D circuit breakers
  • Square D NEMA rated starters
  • Crusher is controlled by a soft start
  • Door mounted amp meter for crusher amperage
  • Hour meter located inside the enclosure
  • PLC/HMI for automated crusher control
  • Crusher Amp Display

 

Hydraulics:

  • 13HP Honda gasoline engine with electric start and backup recoil start
  • (6) Hydraulic jacklegs with lock-out valves
  • The hydraulic jack assemblies are designed for service as a “Run-on” jack, however, we highly recommend the use of cribbing to properly support the portable chassis
  • Six bank valve body for independent control of each jackleg
  • Single bank valve body for crusher motor adjustment
  • Single bank valve body for folding the feed conveyor head section
  • Two bank valve body for adjusting the overscreen conveyor front and rear supports
  • All hydraulic lines are bleed and tested for leaks

 

Safety Guards:

We install all standard guarding, customer will be responsible for compliance with local codes.

 

General:

  • Chassis to be sandblasted, one coat two part epoxy primer and two part urethane finish painted one coat GreyHawk beige with orange and grey highlight stripe on the trailer frame beams.
  • (2) Sets of owners/parts manuals.