Used GreyHawk/Metso HP4RD Portable Plant, Unit #806
Metso/Nordberg HP4 Cone Crusher
- Cast frame with thrust bearing, main shaft and seat liners
- Adjustment ring and clamping ring, clamping by hydraulics cylinders and pin bushings
- Overload protection by double-acting cylinders and accumulators
- Countershaft assembly with shaft, pinion and bushings
- Lock bolt assembly with feed cone
- Bowl assembly with adjustment box
- Hydraulic motor for setting adjustment and ring gear
- Head with inner bushings and spherical bearing
- Eccentric assembly with inner bushing, thrust bearing, gear, counterweight and counterweight liner
- Spherical socket assembly
Additional HP cone features include a package lubrication system consisting of an internal independent pump, oil pressure switch, temperature switch, oil tank with strainer, oil level gauge, thermometers at three locations, (2) oil heater with control panel, oil filter and oil cooler (air-radiator type). Guard for V-belt crusher drive and crusher tools.
WorldWide Crusher Drive Motor 400 HP, 1800 RPM, 460 Volt, 3 Phase, 60 Hz, TEFC Crusher Duty
GreyHawk Heavy Duty Chassis
24” 84# Mainbeam with Triple-Axle Hutch Suspension equipped for semi trailer towing with 11:00 R 22.5 tires on Budd type wheels, air controlled brakes, fifth wheel kingpin, horizontal screen support frame with diamond plate catwalks, conveyor supports, travel lights, reflectors, mud flaps, and V-Belt drive guards.
48" Under Crusher Conveyor (C-2)
C-channel frame equipped with Superior 5" CEMA 'C' channel mount idlers, Superior 12” x 44” vulcanized head pulley, XT30 Hubs, 2-7/16” / 2-7/16” Pillow block bearings, Powertorque 415 shaft mount reducer, WorldWide 15 HP, 1800 RPM, TEFC drive motor sheaves, V-Belts and motor V-Belt guard, Superior 12” x 44” wing tail pulley, XT 30 Hubs, 2-7/16” shaft with Dodge SCM wide slot takeup, Superior 5” CEMA ‘C’ Moxie return idlers, return roll guards, return belt plow, Superior live shaft belt alignment rubber disc rollers, skirt plates with skirtboard rubber, V-Plow 3 ply 3/16” x 1/16” conveyor belting, and Argonics Eraser system.
The Crusher Feed Basket is a weldment which sites over the feed opening, it directs material into the crusher feed opening and reduces spillage. The feed basket is made of ¼” mild steel with a 3/8” base plate. Windows with steel mesh inserts allow the operator to view the material level in the feed basket. The feed basket is typically removed for highway towing.
Feed Basket Overflow to Rear Discharge Conveyor RD
Overflow material is directed to the discharge conveyor.
Adjustable king pin support - Adjustable tubular supports reduce the amount of blocking required in the kingpin area during plant operation, which simplifies set up and tear down. The kingpin supports are lifted and pinned for towing to clear the semi-tractor.
Power hydraulic raise and lower - Six tube in tube style heavy duty run-on jacklegs, with 6" diameter x 18" stroke cylinders to lift the plant into the operating position. Each cylinder is independently controlled from a hydraulic valve for precise control and ease of leveling.
Electric Starters, Wiring and Controls - 6' x 6' x 20" electrical enclosure with structural support to set on grade during plant operation. The enclosure is connected to the plant with 15' electrical cable. The enclosure has a main inlet line surge arrestor, warning horn, lifting eyes and main circuit breaker with door interlocked disconnect linkage. All on-plant equipment is controlled by NEMA rated starters that are mounted in a separate remote control panel. Crusher motor is controlled by a digital solid state reduce voltage starter (soft-start). All push buttons, pilot lights and E-stop switches are heavy duty, 30mm, oil and dust tight devices, and includes an hour meter located inside the enclosure and a door mounted amp meter for crusher amperage.