RB Scott: Equipment, Wear Parts, Service

Connect With Us Facebook

Your process equipment and wear parts specialists

Superior Guardian 6x20 Tandem Screening Plant

#1438042

Carrier chassis

  • Main frame constructed of wide flange structural steel beams
  • Split Quad axle with (16) 11x22.5 radial tires, 4' - 8' - 4' Spacing
    • complete air brake system
    • mudflaps on rear axle
  • Travel lights with brake and directional signals
  • Fifth wheel hitch
  • (8) fixed, structural steel cribbing legs
  • (2) swing down king pin supports
  • Common Grease points - 1-2 locations to grease entire plant

 

(2) Superior Guardian 6203 Horizontal Vibrating Screen

  • Supply and Installation for a 6x20 3 deck, all pertinent items and components including:
    • adjustable motor base, motor sheave, screen sheave, v-belts, drive guard
    • Screen and all pertinent items and components are supplied by Superior
  • Price includes the following items:
    • 40 HP TEFC, 1200 RPM, 460 volt, 3 phase, 60 hz, screen drive motor
    • screen subframe
  • Screen is installed to operate in the horizontal position
  • (1) Right hand drive (1) Left hand drive
  • Side tension on bottom deck
  • Vertical dampening system

 

Screen discharge chutes

  • Fixed chutes
  • Constructed of 1/4" Mild Steel with 1/4" AR liners
  • Top deck chute discharges onto top deck cross conveyor or down to Middle deck cross conveyor
  • Middle deck chute discharges onto middle deck cross conveyor, blends down to bottom deck cross conveyor
  • Bottom deck chutes discharges onto bottom deck cross conveyor, or down to fines conveyor

 

Fines hopper

  • AR liner not included
  • adjustable rubber flashing full length

 

(3) 42" wide x 12' long reversing cross conveyors

  • Structural steel channel main frame
  • Mounted on angle iron slide track to manually move to discharge from either side of chassis
  • Receive oversize material from respective middle and bottom decks
  • Class II head end drive
  • 5 HP motor, v-belt drive with drive guard
  • Dodge shaft mount reducer
  • Head pulley - 10" diameter drum, crown face, 3/8" diamond lagging
  • Tail pulley - 10" diameter wing pulley
  • Shafts - turned and polished
  • Dodge bearings
  • Manual screw take-ups
  • Carry idlers - C5, 20 degrees trough, channel mount, spaced 26" OC
  • Belting - 2 ply, 3/16" x 1/16" 220 PIW
  • Belt splice - steel mechanical fasteners
  • Primary belt scraper - Exterra® Belt Cleaner
  • Cassette style cross convetor set up

 

(2) 24" fines conveyors (reversible) for primary screen

  • Structural steel channel main frame
  • Discharges material to off plant conveyor or to fines conveyor on secondary screen
  • Class II head end drive
  • 10 HP motor, v-belt drive
  • Dodge shaft mount reducer
  • Head pulley - 12" diameter drum, crown face, 3/8" diamond lagging
  • Tail pulley - 12" diameter drum, crown face, 3/8" diamond lagging
  • Shafts - turned and polished
  • Dodge bearings
  • Manual screw take-ups
  • Carry idlers - C5, 20 degrees picking, channel mount, spaced approximately 27" OC
  • Return idlers - C5, flat rolls, spaced 10' OC
  • Belting - 2 ply, 3/16" x 1/16" 220 PIW
  • Belt splice - steel mechanical fasteners
  • (2) Primary belt scraper - Exterra® Belt Cleaner
  • Fixed Chutes to direct material onto each cross conveyor

 

60" fines conveyor

  • Structural steel channel main frame
  • Discharges to off plant conveyor
  • Class II head end drive
  • 20 HP motor, v-belt drive
  • Dodge shaft mount reducer
  • Head pulley - 12" diameter drum, crown face, 3/8" herringbone lagging
  • Tail pulley - 12" diameter Chevron® wing pulley
  • Shafts - turned and polished
  • Dodge bearings
  • Manual screw take-ups
  • Carry idlers - C5, 20 degrees picking, channel mount, spaced approximately 27" OC
  • Return idlers - C5, flat rolls, spaced 10' OC
  • Belting - 2 ply, 3/16" x 1/16" 220 PIW
  • Belt splice - steel mechanical fasteners
  • Primary belt scraper - Exterra® Belt Cleaner

 

Walkway

  • 3/16" diamond tread plate along both sides and feed end of screen
  • Includes toe board, and two-rail handrail, bolt on
  • Walkway access on both sides of the chassis with steep angle stair access
  • Drain holes

 

Hydraulic "lift only" leveling jacks

  • (8) 6" x 20" hydraulic cylinders
  • (8) manual lever valves; (1) for each cylinder
  • 13HP Honda Motor gasoline over hydraulic, enclosed cabinet

 

Overhead Safety tie off

  • Safety tie off over plant for workers to tie off when working on screen
  • Folds down for transport

 

Electrical control panel

  • NEMA 4 enclosure and NEMA SQUARE D electrical components
  • Wired to on-plant motors
    • (2) 40 HP screen drive motor
    • (1) 15 HP fines conveyor drive motor
    • (2) 10 HP fines conveyor drive motor
    • (6) 7.5 HP reversing cross conveyors
    • (2) Screen Amp guage on outside of panel
    • Hour meter inside panel
    • Warning horn and light
    • Labelled start/stop pushbuttons and E-stop pushbutton mounted on door of electrical panel
    • Mounted on skid frame with lifting eyes
    • Power cables from motors to place panel 30' from plant,
    • Painted to match plant
  • (2) Additional #2 starters for off plant conveyors

 

Electrical

  • Required power is 480 v/ 3 ph / 60 hz
  • Control panel and wiring are included

 

Guarding

  • Price includes standard guarding
  • Customer is responsible to have guarding inspected

 

Paint

  • (1) coat primer; (1) finish coat enamel available in Superior Beige with Yellow Guarding

 

 Owner's manual

  • (1) copy included for operation and maintenance