RB Scott: Equipment, Wear Parts, Service

Connect With Us Facebook

Your process equipment and wear parts specialists

Used Superior Guardian 6x20 2-Deck Sump Plant with Schurco Pump, Unit #1041


Carrier chassis

  • Main frame constructed of wide flange structural steel beams
  • Tandem axle with (12) 11x22.5 radial tires
    • complete air brake system
    • mudflaps on rear axle
  • Travel lights with brake and directional signals
  • Fifth wheel hitch
  • (4) fixed, structural steel cribbing legs
  • Common Grease points -Multiple locations to grease entire plant

 Superior Guardian 6202 Horizontal Vibrating Screen

  • Supply and Installation for a 6x20 2 deck, all pertinent items and components including:
    • adjustable motor base, motor sheave, screen sheave, v-belts, drive guard
    • Screen and all pertinent items and components are supplied by Superior
  • Price includes the following items:
    • 40 HP TEFC, 1200 RPM, 480 volt, 3 phase, 50 hz, screen drive motor
    • screen subframe
  • Screen is installed to operate in the horizontal position
  • Manual tilt up motor mount
  • Right hand drive

 Screen discharge chute

  • Constructed of 1/4" Mild Steel with 1/4" AR liners
  • Top deck chute discharges over the kingpin end of the chassis or onto bottom deck cross conveyor
  • Bottom deck chutes discharges onto bottom deck cross conveyor

 Fines hopper

  • 1/4" AR Construction

 Spray Bars

  • (9) 2" Galvanized spray bars and elbows, brass nozzles
  • Bottom deck spray bars to have double row of staggered brass nozzles
  • Flexible rubber hosing from manifold to spray bars
  • Manually adjustable spray bar for each spray bar, mounted below walkway

 Water Manifold

  • 8" bolt flange at ground level for fresh water hookup
  • Fresh water feeds in from end
  • Distributes water to: spray bars, slurry hopper, sump (make up water), and fines hopper
  • Wye strainer to prevent large debris from entering

 Slurry Hopper

  • Hydraulically folds from transport to operating position
  • Accepts feed from conveyor, lined for wear protection
  • Spray bars mounted inside hopper

 (1) 30" wide x 12' long reversing cross conveyors

  • Structural steel channel main frame
  • Angle iron slide to manually move to discharge from either side of chassis
  • Receive oversize material from respective top and bottom decks
  • Class II head end drive
  • 5 HP motor, v-belt drive with drive guard
  • Dodge shaft mount reducer
  • Head pulley - 10" diameter drum, crown face, 3/8" diamond lagging
  • Tail pulley - 10" diameter wing pulley
  • Shafts - turned and polished
  • Dodge bearings
  • Manual screw take-ups
  • Carry idlers - C5, 20 degrees trough, channel mount, spaced 26" OC
  • Belting - 3 ply, 3/16" x 1/16" 330 PIW
  • Belt splice - steel mechanical fasteners
  • Primary belt scraper - Exterra® Belt Cleaner


  • Sump constructed of 3/8" AR400 steel
    • Pump flange for mounting pump
    • 4000 Gallon capacity


  • 3/16" diamond tread plate along both sides and feed end of screen
  • Includes toe board, and two-rail handrail, bolt on
  • Walkway access on both sides of the chassis with steep angle stair access
  • Drain holes

 Hydraulic "lift-only" leveling jacks

  • (4) 6" x 20" hydraulic cylinders
  • (4) manual lever valves; (1) for each cylinder
  • 9hp Honda gasoline over hydraulic pump unit


  • Required power is 480 v/ 3 ph / 50 hz
  • Control panel and wiring are not included


  • Price includes standard guarding
  • Customer is responsible to have guarding inspected


  • (1) coat primer; (1) finish coat enamel available in Superior Beige/Yellow Guarding

 Owner's manual

  • (1) copy in English and (1) copy in Spanish included for operation and maintenance

 Screen Media

  • (2) Decks of Tema WS85


Schurco Slurry Pump (Qty 1):

  • 10" x 8" (S Series)
  • Rubber casing liners
  • Rubber impeller
  • Centrifugal seal/grease lubricated
  • Overhead motor table
  • Motor – 250HP, 1800 RPM, 230/460 volt, 3-phase, 60 cycle, TEFC, inverter duty
  • V-belt drive sheaves and belts
  • Drive guard
  • Fabricated base
  • GPM – 3,453
  • Suction Hose
  • Discharge Adapter

Note: On final determination of the actual pipe system, and total dynamic head, should a smaller or larger motor be required, the price may be adjusted accordingly.