GreyHawk Metso 7x20 Tandem Screen Plant Unit #1639
SN: #1337/4046/4047
EQUIPMENT ON LEASEEquipment As Follows:
METSO 7x20 THREE DECK HORIZONTAL SCREEN (1 LEFT HAND DRIVE/1 RIGHT HAND DRIVE)
- The new triple shaft Metso horizontal screen is designed for maximum efficiency and performance
- Coil Springs and dampers
- 3/8” Thick Side Plates with Huck Bolt Construction
- Side Tension decks with seal strips for 4’ screen panels
- Heavy Duty Tube Steel Decks with Herringbone Cross Bracing
- Vibrating Mechanism (190mm bearings) with Oil lubrication
- Carriage Bolts used to retain clamp bars – Standard is 4’ long bars
- AR lined Feedbox and AR lined Discharge Lip
- Variable speed drive standard with motor mount and belt guard and tensioning device
- Hand access on triple deck screens. Spray Bar knockouts, bottom deck Feed end curtain
- Hand of drive is Right Hand
- Side tension single crown
- Medium Scalper Deck – includes heavy duty side tension top deck, heavier feedbox liner and heavier top discharge lip.
- Media not included
- Side tension single crown
- Media not included
- Side tension single crown
- Media not included
- Installation Angle 0°
- Elliptical stroke 5/8” -3/4”
- RPM 675-875
- Separating G Force: 4.8-6.5
- Top deck
- Middle deck
- Bottom deck
GREYHAWK PORTABLE TANDEM SCREEN PLANT CHASSIS
- MAIN CHASSIS
- Heavy Duty Mainbeam
- Quad-axle Hutch Spring Suspension with 49-1/2” axle spacing
- Qty 16 11R22.5 tires on hub piloted wheels
- Air controlled brakes on all four axles
- LED side marker and tail lights
- Catwalk on three sides of each screen, diamond floor plate, including handrails and toe boards, with (2) access ladders included.
- Fold down kingpin supports
- Chutes-Primary & Secondary Screen
- Top deck to top cross conveyor
- Middle deck to middle cross conveyor/bottom cross conveyor/fines conveyor
- Bottom deck to middle cross conveyor/bottom cross conveyor/fines conveyor
- OVERHEAD SPLITTER CONVEYOR-42”
- Channel frame design
- Superior 5” CEMA C channel mount picking idlers
- Superior 5” CEMA C return idlers
- Superior Exterra belt scraper
- 3 ply, 3/16” top cover conveyor belting
- Full length rubber skirting
- Head Pulley
- VDG motorized drum pulley 16”
- 20HP motor
- Dodge SCM pillow block bearings
- Tail Pulley
- Superior 12” wing pulley
- Dodge SCM bearings
- Takeups
- UNDERSCREEN CONVYEOR (PRIMARY SCREEN)-60”
- Channel frame design
- Superior 5” CEMA C channel mount picking idlers
- Superior 5” CEMA C return idlers
- Superior Exterra belt scraper
- 3 ply, 3/16” top cover conveyor belting
- Full length rubber skirting
- Head Pulley
- Superior 12” drum pulley
- Dodge SCM pillow block bearings
- Master PT #5 shaft mount reducer
- WEG 20HP motor
- Takeups
- Tail Pulley
- Superior 12” wing pulley
- Dodge SCM bearings
- UNDERSCREEN CONVYEOR (SECONDARY SCREEN)-60”
- Channel frame design
- Superior 5” CEMA C channel mount picking idlers
- Superior 5” CEMA C return idlers
- Superior Exterra belt scraper
- 3 ply, 3/16” top cover conveyor belting
- Full length rubber skirting
- Head Pulley
- Superior 12” drum pulley
- Dodge SCM pillow block bearings
- Master PT #5 shaft mount reducer
- WEG 20HP motor
- Tail Pulley
- Superior 12” wing pulley
- Dodge SCM bearings
- Takeups
- TOP CROSS CONVYEOR- QTY (1)-48”
- Channel frame design
- Superior 5” CEMA C flat carrier idlers
- Superior 5” CEMA C return idlers
- Superior Exterra belt scraper
- 3 ply, 3/16” top cover conveyor belting
- Full length rubber skirting
- Head Pulley
- Superior 10” drum pulley
- Dodge SCM pillow block bearings
- Master PT #4 shaft mount reducer
- WEG 10HP motor
- Tail Pulley
- Superior 10” wing pulley
- Dodge SCM bearings
- Takeups
- CROSS CONVYEOR- QTY (4)-24”
- Channel frame design
- Superior 5” CEMA C flat carrier idlers
- Superior 5” CEMA C return idlers
- Superior Exterra belt scraper
- 3 ply, 3/16” top cover conveyor belting
- Full length rubber skirting
- Head Pulley
- Superior 10” drum pulley
- Dodge SCM pillow block bearings
- Master PT #2 shaft mount reducer
- WEG 7.5HP motor
- Tail Pulley
- Superior 10” wing pulley
- Dodge SCM bearings
- Takeups
- HYDRAULICS:
- Gas powered hydraulic power unit with electric start and recoil backup
- (6) Hydraulic jacklegs with lock-out valves, 18” stroke
- The hydraulic jack assemblies are designed for service as a “Run-on” jack, however, we highly recommend the use of cribbing to properly support the portable chassis
- Six bank valve body for independent control of each jackleg
- Raise/lower of the overhead splitter conveyor
- ELECTRICAL:
- NEMA4 enclosure
- Enclosure is bolted to a steel support frame for setting on grade during operation
- Lifting eyes
- Connected to plant with 15’ of cable to allow the customer to position the enclosure
- Door interlocked disconnect linkage
- Warning horn
- Circuit breakers
- NEMA rated starters
- Overhead Splitter Conveyor – 1@20HP/each
- Primary Underscreen Discharge Conveyor – 1@20HP/each
- Secondary Underscreen Discharge Conveyor – 1@20HP/each
- Top Cross Conveyor – 1@10HP/each
- Cross Conveyors – 4@7.5HP/each
- Screen – 2@50HP/each
- Hour meter
- Pushbutton start/stop control
SAFETY GUARDS:
We install all standard guarding, customer will be responsible for compliance with local codes.
GENERAL:
- Paint
- Sandblasted
- Two-part epoxy primer
- Two-part urethane topcoat
- Chassis Color-GH Beige
- Handrail & Guarding Color-GH Orange
- Decals-Orange & grey striping
- (2) sets of owners/parts manuals.